Have you ever wondered what you should do to your pool when it rains? If so, read on. It’s an important one to consider if you own a pool. Chemical and physical changes are brought on by severe rainfall, which causes pools to undergo several alterations. Swimming pool construction has grown in popularity over the last decade.
Rainwater affects the pool’s pH and Alkalinity levels, while excessive rainfall adds water to the pool that you don’t need. Then there are the rainstorms that bring with them a slew of pollutants. In Pune, Apram Pools is a well-known and reputable swimming pool construction company that designs and swimming pool maintenance services.
Keep reading for advice on keeping your pool’s chemicals balanced. For crystal clean water and a welcoming environment for swimmers, here are seven things you should do after a rainstorm to your pool.
1. Make sure your water level is enough
Check your pool’s water level after it rains, especially after a hurricane or storm.
Your water level is probably much above the skimmer hole. This affects water filtration and chemistry.
This problem is easy to fix.
If the water level in your pool is over the halfway point of the skimmer, start slowly draining it. Your pool pump is required for this.
Pool water may be removed by following these steps:
• Select “Waste” or “Backwash” on your pump.
• To begin, connect your backwash hose.
• Turn on the pool pump
• Watch water level as pump empties.
• Stop pumping when water reaches mid-skimmer.
If you want to clean faster, connect your pool vacuum to your skimmer instead of running your pump to backwash. While vacuuming the pool floor, lower the water level.
2. Turn on the filtration system if you like
Getting your water moving is the next step once your water level has been restored.
IMPORTANT: Empty your pump and pool skimmer baskets before turning on your pump again. Set your pump to “FILTER” at that point.
You might also want to:
• Start warming your pool water by turning on your pool heater.
• Ensure your pool water testing kit and chemicals are ready to use.
3. Shock the pool
You can give your water a slight boost even if you aren’t ready to adjust your pool’s chemistry. Your pool’s chlorine levels will drop significantly after a severe rainstorm because of the fight against pollutants.
Re-introducing chlorine to your pool after a rainstorm is as simple as shocking. Also, the pump must be running continuously during the procedure. Your main drain can take care of some cleaning while you’re still moving about.
Although a single shock treatment will not be enough to balance your water, it will continue to function in the background as you clean your pool.
Your chlorine levels will be closer to normal when you begin changing chemicals. Find Dependable and Experienced Swimming Pool Consultants in Pune.
4. Surface-skim debris
You must remove any floating debris from your water as soon as you notice it.
If you wait, it will eventually drop to the bottom of the pool. There is no better way to keep your water crystal clean than by vacuuming regularly.
Leaves, twigs, and bugs make up most of the pool’s surface litter. However, the purpose of this exercise is to eliminate anything visible.
Seize a skim and begin fishing for anything within easy reach.
Installing an automated skimmer in your pool will make future skimming much faster. Attached to your pool’s return jets, these nifty devices rise above the water’s surface to gather any floating trash.
5. Vacuum and brush the pool’s surface
The smoothness of the water’s top means you can now “dive down” to the pool’s bottom.
Start cleaning the walls and stairs, but don’t forget about the rest of the house. It’s a strong bet that toxins are hiding even if they appear clean, ready to increase and render your pool green or hazy.
Connect your vacuum to the skimmer and clean the pool floor once you’ve finished cleaning. For the most outstanding results, vacuum the whole length of the pool.
It’s time to go on to the next phase if you have an automated pool cleaning.
Avoid using a vacuum cleaner by pushing trash into the main drain with an old toothbrush. It will be sucked up by the main drain and sent directly to the filter. Call us to book the best pool cleaning service in Pune.
6. Your water should be tested
This is perhaps the most crucial thing to do after it rains. Why? Because it’s vital to maintain clean water. It’s the only method to prevent green or hazy rainwater.
In a word, rain has the following effects on pool chemistry:
• Acid rain lowers the pH of your water.
• The total Alkalinity of rainwater is likewise reduced.
• Total Alkalinity is more sensitive to changes than pH because Alkalinity preserves your water’s pH.
• When it rains heavily, pollutants are introduced to your water, reducing the amount of chlorine.
• A high or low pH compromises the efficacy of chlorine.
Begin by checking your water to see whether it’s safe.
• Check pH
• A pH of 7.4 to 7.6 is considered ideal.
• Verify the Alkalinity Total
• The best TA is between 80 and 120 ppm.
• Check Calcium Hardness
• Healthy CH levels are between 100 and 300 ppm (the lower, the better)
• Verify sanitizer and chlorine levels
• A minimum of 3 ppm (but 1-2 ppm higher is OK)
7. Reset the pH of your water by adjusting the chemicals.
Knowing which chemicals in your water require the most significant change should be evident after water testing. Swimming pool builders can be found in many sizes and colours, from those who work on some of the’s tallest pools to smaller household pools.
There are times when starting with TA is the best course of action since it stabilizes your pH. pH, CA, and Sanitizer are the following three steps.
Adjusting pool chemicals:
Adjusting pH
• You can use soda ash or sodium carbonate to raise the pH of your swimming pool.
• Sodium bisulphate or muriatic acid can be used to lower the pH of your pool.
Adjusting Total Alkalinity
• Baking soda may be used to raise the TA of your pool. Dry acid or muriatic acid can be used to lower your pool’s TA level. Adjusting Calcium Hardness
• Add calcium chloride to your pool to raise its CH level.
• Dilute your water to reduce CH.
